News Center

What factors are typically considered when selecting and designing the layout for personnel positioning in a chemical plant?


Category:

Author:

A Long

Source:

admin

Release Date:

2025-05-07

The selection and layout of personnel positioning systems in chemical plants must be evaluated comprehensively. Security requirements, technical feasibility, cost-effectiveness, compliance, and real-world scenario adaptability , The following are the key considerations and recommendations:

I. Requirements Analysis and Core Objectives

  1. Security Priority
    • Risk area coverage : Clearly define the positioning accuracy requirements for high-risk areas (such as reactor areas, tank farms, and loading/unloading zones) (e.g., UWB positioning accuracy must reach 10-30cm , the accuracy of Bluetooth beacons is approximately 1–3 meters ).
    • Emergency Response : Ensure that, in the event of an accident, the system can Within 30 seconds Locate the trapped individuals and integrate with video surveillance and access control systems.
    • Special Operations Management For high-risk operations such as hot work and confined-space entry, personnel trajectory tracking must be implemented (e.g., by storing…). 90-day historical data ) and timeout alerts (e.g., a warning is triggered if the stay exceeds 2 consecutive hours).
  1. Manage Requirements
    • Attendance and Work Hour Tracking : Automatically generate employee attendance reports using location data, reducing manual calculation errors.
    • Personnel density monitoring : Real-time counting of the number of people in a designated area to prevent overcapacity operations (e.g., ensuring that the number of personnel in a confined space does not exceed 3 people ).
    • Training and Permission Management : Assess employee skill proficiency using location data and dynamically adjust access permissions for high-risk areas.

II. Technical Selection Comparison

Technology Type

Core Principle

Applicable Scenarios

Advantage

Disadvantage

Typical Cost (per card)

UWB Ultra-Wideband Positioning

Calculate position using time-of-flight (ToF) measurements. High-Risk Core Zone, Dense Equipment Area High accuracy (10–30 cm) and strong anti-interference performance. High deployment costs (requiring a base station to be installed every 30 meters) ¥800-1500

Bluetooth beacon positioning

Triangulation-based localization using RSSI signal strength Corridors, warehouses, and general production areas Low cost (single beacon: ¥200–500) and easy to deploy. Accuracy is affected by environmental interference (1–3 meters). ¥300-600

LoRa wireless positioning

Low-Power Wide-Area Network (LPWAN) + TDOA Algorithm Large industrial parks, remote plant areas Wide coverage (1–3 km per base station) and long battery life. Poor real-time performance (positioning interval ≥ 5 seconds) ¥500-800

GPS/Beidou positioning

Satellite signal positioning Perimeter patrol and vehicle dispatching within the plant area Full outdoor coverage, with no infrastructure costs. No indoor signal; low accuracy (5–10 meters) ¥200-400

RFID-based area positioning

The reader scans the electronic tag. Factory entrance and exit, key passageways Extremely low cost (single label: ¥50–100) It can only determine the presence of a region, but cannot perform real-time tracking. ¥100-300

Selection Recommendations :

  • Core Risk Area : Prioritize adoption UWB + Bluetooth Beacon Hybrid deployment: UWB ensures high precision, while Bluetooth fills coverage blind spots.
  • General Production Area : A Bluetooth beacon–LoRa combination that balances cost and accuracy.
  • Outdoor/Vehicle : GPS/Beidou + LoRa, enabling a closed-loop tracking system across the entire plant.
  • Temporary Work Area : Portable Bluetooth beacon + mobile base station, for rapid deployment.

III. Key Considerations in Layout Design

  1. Signal Coverage Planning
    • Base station density : UWB base station spacing ≤ 30 meters, Bluetooth beacon spacing ≤ 10 meters, LoRa base station spacing ≤ 500 meters (in open areas).
    • Three-dimensional coverage For multi-story industrial buildings, base stations should be deployed on each floor to avoid signal penetration losses (concrete walls can attenuate signals by 20–30 dB).
    • Redundant design Key areas employ “dual‑base‑station cross‑coverage,” ensuring location services remain available even in the event of a single-point failure.
  2. Explosion-proof and Protective
    • Explosion-proof certification : The positioning device must pass through Ex dⅡCT6 Gb Certification: Intrinsically safe type (Ex ib) is suitable for Zone 0.
    • Protection rating Outdoor equipment shall meet IP68, indoor equipment IP65, and corrosion‑resistant coatings shall withstand exposure to chemical gases.
    • Electromagnetic Compatibility : Tested in accordance with IEC 61000‑4 to prevent mutual interference with DCS and SIS systems.
  3. Wearing and Compatibility
    • Wearing method The positioning tag must be integrated into the safety helmet, employee badge, or reflective vest to ensure 100% compliance with佩戴.
    • Multi-modal fusion : Supports NFC-based access control, one-touch SOS emergency alert, and integrated gas detection (e.g., a location‑tracking card paired with a four‑in‑one gas sensor).
    • Battery life : High-risk area devices offer ≥7 days of battery life, while general‑area devices provide ≥30 days; wireless charging or magnetic fast charging is supported.

IV. Compliance and Safety Standards

  1. Regulatory Compliance
    • Work Safety Law : Must comply with the personnel positioning requirements specified in the “Safety Code for Special Operations in Enterprises Handling Hazardous Chemicals” (GB 30871-2022).
    • Data Security : Location data is transmitted using AES‑256 encryption, stored in compliance with the Personal Information Protection Law, and non-essential information is anonymized.
    • Security Assessment Certification : The system must pass through Level 3 of MLPS 2.0 Authentication to prevent network attacks from causing positioning outages.
  1. Emergency Coordination
    • Integrate with the SIS system : When personnel inadvertently enter a high-risk area, an interlock shutdown is automatically triggered (e.g., closing valves and cutting off power).
    • Interoperates with the fire protection system : During a fire, optimal evacuation routes are generated based on location data to prevent overcrowding and stampedes.
    • Integrate with the healthcare system : After an accident, quickly access personnel health records (such as blood type and allergy history) to improve rescue efficiency.

V. Balancing Costs and Benefits

  1. Initial investment
    • Hardware costs : Location tags (¥300–1,500 each) × number of users + base stations (¥5,000–20,000 each) × quantity.
    • Software cost : Platform licensing fee (RMB 100,000–300,000 per year) + custom development costs (e.g., integration with MES or ERP systems).
    • Construction cost : Wiring, explosion-proof installation, and commissioning costs (accounting for approximately 20% of the total cost).
  2. Long-term returns
    • Accident rate reduction : Following deployment, a certain petrochemical enterprise reported a 40% reduction in near-miss incidents and an annual decrease in direct economic losses of approximately ¥5 million.
    • Compliance Cost Savings : Avoid production shutdown penalties resulting from non‑compliance (with a maximum of RMB 100 million per instance).
    • Improved Management Efficiency : Reduce manual inspection man-hours by 30% and lower training costs by 25%.

VI. Implementation Steps and Pitfall Guide

  1. Implementation Process
    • Phase 1 (January–February) : Requirements gathering, risk assessment, and technology selection.
    • Phase 2 (March–April) : 3D modeling, base station site planning, and explosion-proof certification.
    • Phase 3 (May–June) : Hardware installation, software debugging, and stress testing (simulating 1,000 concurrent users).
    • Phase 4 (July and beyond) : Employee training, policy revisions, and continuous improvement.
  2. Frequently Asked Questions and Solutions
    • Signal dead zone : By deploying Repeater Alternatively, adjust the base station’s orientation to avoid obstruction from metal pipes and large equipment.
    • Position drift : Adopt Kalman filter algorithm Eliminate multipath effects and refine the position using map-based constraints.
    • Employee resistance : through Points-based reward system (For example, redeeming safety‑behavior points for gifts) to increase the willingness to wear it.

Conclusion

The key to the success of a chemical plant personnel positioning system lies in “Precise scenario alignment, strict adherence to safety standards, and a balanced cost–benefit analysis” . It is recommended to adopt “UWB + Bluetooth + LoRa” Multi-Mode Fusion Technology , combined with Explosion-proof design, emergency interlock, data compliance The three core modules will be rolled out in phases. The ultimate goal is to leverage technology to upgrade “human‑based safety measures” to “technology‑driven safety,” thereby shifting chemical‑industry production safety from a post‑incident accountability model to a proactive, preventive approach.