News Center

In-Depth Insights: The Seven Key Factors Affecting the Accuracy of Personnel Positioning Systems and Their Solutions


Category:

Author:

Aviation and Optical-Electronic Technology

Source:

www.hangfeigd.com

Release Date:

2026-06-05

The safety officer at a chemical plant said with resignation that, during system acceptance testing, the accuracy… 10 Centimeters—after three months, the error has become 2 meters. This is not an isolated case. We visited 30 At multiple project sites, the most common influencing factors have been identified and categorized into 7 A sector.

Factor 1: Walls and metal cabinets can weaken the signal.

Signals propagate through the air but attenuate when they encounter concrete walls, metal shelving, or large equipment. A single wall can reduce signal strength by 60 to 70 percent, increasing positioning error by about half a meter. If workers enter a narrow corridor, the signal may be completely lost, leaving the positioning point stuck at the entrance.

Tip Before deployment, conduct a site survey using signal‑testing tools, paying particular attention to corners and areas with high metal density. Prior to construction, Hangfei Optoelectronics’ engineering team will perform a full‑site signal simulation, identifying locations with weak coverage and pinpointing where additional base stations are needed, marking these areas in advance.

Factor two: Metal surfaces can cause signal interference.

Metal pipes, storage tanks, and shelving can cause signal reflections. As a result, the base station receives both direct and reflected signals, which can lead to inaccurate positioning. There are three common manifestations:

  • Metal shelving area: When a person stands still, the positioning point fluctuates wildly within a radius of one to two meters, and the electronic fence triggers frequent alarms.
  • Utility tunnels or underground passages: When the direct path is obstructed, the positioning result may be offset into the adjacent tunnel.
  • Near the large cylindrical tank: the trajectory exhibits abrupt, jagged jumps, appearing highly unnatural.

Solution : Choose a system with anti-reflective coating. Hangfei Optoelectronics’ positioning algorithm has been specifically optimized for metal environments, reducing errors caused by reflections by more than 80%.

Factor Three: Too Few Base Stations or Poorly Positioned Ones

To cut costs, some projects install only two or three base stations per workshop. When the angles between adjacent base stations are too narrow, even minor ranging errors can be magnified, causing straight-line movement to deviate into curved paths. Ideally, high-risk areas should be covered by at least four base stations simultaneously.

Q&A
Q: What is the appropriate height for installing a base station?
Answer: Usually 3 to 5 Meters. Too low, and it’s easily obstructed by people and vehicles; too high, and signal attenuation becomes significant.

Factor Four: The algorithm is not adapted to the real-world environment.

Many systems achieve high accuracy during testing in open exhibition halls, but their performance deteriorates once deployed in a factory. This is because factories are characterized by the constant movement of forklifts, dense pedestrian traffic, and frequent equipment start‑ups and shutdowns. If the algorithm relies solely on fixed parameters, it will either respond too slowly, resulting in trajectory lag, or generate excessive noise, causing positional jitter. The algorithm’s capabilities ultimately determine how effectively the hardware can perform.

In a nutshell. When selecting equipment, don’t rely solely on hardware specifications—ask the supplier to conduct a live demonstration in an environment similar to your factory.

Factor 5: Data during peak hours tends to become congested.

During peak commuting hours or large-scale gatherings, hundreds or even thousands of location tags may simultaneously transmit data. When the base station cannot handle the load, the following issues may arise:

  • Data collision: Heartbeat packets from some tags were lost, causing the corresponding personnel to temporarily disappear from the map.
  • Increased latency: originally 1 Refreshes once per second, becoming 5 seconds, even 10 It updates only once per second.
  • Base station overload: In extreme cases, positioning across an entire area may fail.

Tip : Inquire with the supplier about the actual number of tags that a single base station can stably support. According to field tests conducted at multiple thousand‑person factories, a single base station can support 150 More than one tag reports at high frequency simultaneously, ensuring no data loss during peak periods.

Factor Six: Hardware Cannot Withstand Harsh Environments

Some devices boast high waterproof and dustproof ratings, but after just a few months of use in dusty workshops, dust accumulates in the seams, compromising the seals. Moisture then penetrates, corroding the circuit boards and causing the signal to weaken progressively. Corrosive gases in chemical plants, sub-zero temperatures of minus twenty to thirty degrees Celsius in northern winters, and intense summer sun exposure in the south can all accelerate the aging of standard hardware.

Factor 7: Signal interruptions occur when switching between indoor and outdoor environments.

Many enterprises operate both outdoor storage yards and indoor workshops. Outdoors, they rely on the BeiDou system; as soon as personnel enter the workshop, satellite signals are immediately lost. If separate systems are used indoors and outdoors, data often fails to align, creating management blind spots. The ideal solution is a unified backend that seamlessly switches from outdoor to indoor positioning without any interruptions.

Hangfei Optoelectronics’ integrated positioning platform supports BeiDou, UWB Bluetooth automatic recognition and switching allow management personnel to view the entire plant’s location history on a single interface, eliminating the need to toggle between two separate maps.

Conclusion: Precision issues are mostly caused by a combination of factors.

No company’s system can guarantee 100% accuracy in every environment. However, most accuracy issues don’t require replacing the entire hardware setup; instead, you can systematically troubleshoot by addressing each of the seven points mentioned above: whether signal blockages have been mitigated with additional base stations, whether metal reflections have triggered the anti‑multipath algorithm, whether the base station layout is optimal, whether congestion occurs during peak periods, and whether the hardware is well‑suited to the local environmental conditions. Identifying the two or three most critical weak points often yields significant improvements at a relatively low cost.

If you’re struggling with inaccurate positioning, start by reviewing this checklist yourself. You’re also welcome to contact HANGFEI Optoelectronics’ technical experts for a free on-site signal assessment. We don’t just sell equipment—we excel at helping businesses pinpoint the root of their challenges.