How much does a personnel positioning card for chemical plants cost per unit? _ Instructions for using personnel positioning cards
Price and User Guide for Chemical Plant Personnel Location Cards
I. Price of Personnel Location Cards
Chemical Plant Personnel Location Card Prices vary depending on the technology type, feature configuration, and supplier; the general price range is as follows:
- Basic functional type : The price is at 50–200 yuan per sheet , suitable for simple positioning and attendance applications, such as Bluetooth beacon-based location cards.
- High-precision positioning type : The price is at 200–1,000 yuan per sheet , employing UWB technology, it achieves centimeter-level positioning accuracy, making it suitable for complex environments and high-precision applications.
- Multi-functional integrated type : The price is at Over 1,000 yuan per sheet , integrating functions such as positioning, SOS emergency alerts, and environmental monitoring, it is suitable for high-risk working environments.
Price influencing factors :
- Type of technology UWB technology is relatively expensive, whereas Bluetooth or LoRa technologies are more cost-effective.
- Feature Configuration : Whether it integrates SOS alarm, voice communication, environmental monitoring, and other functions.
- Brand and Quality : Well-known brand products are more expensive, but they offer greater assurance in terms of quality and after-sales service.
- Purchase Quantity : Bulk purchases qualify for a certain discount.
II. Instructions for Using the Personnel Location Card
- Wearing Requirements
- Wearing position : The positioning card must be worn on a conspicuous,不易脱落 location on the person, such as an employee ID badge, hard hat, or belt.
- Wearing Guidelines Ensure that the positioning card antenna is not obstructed to prevent inaccurate positioning caused by signal blockage.
- Special Scenarios : In special environments characterized by high temperature, high pressure, and severe corrosion, it is necessary to wear a dedicated positioning card that is explosion-proof, waterproof, and corrosion-resistant.
- Operating Procedure
- Power On and Connection : Press the power button on the positioning card to turn it on; the device will automatically connect to a base station or receiver.
- Status indicator light :
- The green light is on continuously. : The equipment is operating normally.
- Red light flashing : Battery level is low; please recharge promptly.
- Yellow light flashing : In case of equipment failure or signal anomalies, please contact the administrator for resolution.
- Data Viewing Managers can use the backend system to view real-time information such as personnel locations, movement tracks, and dwell times.
- Charging and Maintenance
- Charging method : Positioning cards are typically charged via USB or in a dedicated charging cabinet, with a charging time of approximately 2–4 hours. Battery life varies depending on the battery capacity.
- Charging Precautions :
- Use the original charger to prevent overcharging or deep discharging.
- Avoid high-temperature environments during charging to prevent battery damage.
- Regular maintenance :
- Inspect the positioning card’s exterior monthly to ensure there is no damage, water ingress, or other issues.
- Conduct a functional test once per quarter to ensure that features such as positioning and alarm functions are operating properly.
- Emergency Response
- SOS alarm When personnel encounter an emergency, they can press the SOS button on the positioning card, and the system will immediately send an alert to the central control room and the mobile phones of management personnel.
- Stationary Alarm : If a person remains stationary for an extended period (e.g., unconscious or trapped), the system automatically triggers an alarm.
- Low Battery Alert When the positioning card’s battery level drops below 20%, a low-battery alert is automatically sent; please recharge it promptly.
- Troubleshooting :
- If the positioning card cannot connect to the base station, check whether it is outside the signal coverage area or if the device is malfunctioning.
- If the positioning card gets wet, immediately power off the device and remove the battery. Use absorbent paper to blot away any moisture, then allow it to dry completely before using it again.
- Management Requirements
- Distribution and Collection :
- Upon onboarding, the safety management department shall issue a location‑tracking card and maintain a corresponding record.
- Upon an employee’s departure or transfer to a new position, the location‑tracking card must be returned, and the security management department will revoke the associated access permissions.
- Permission Management :
- Different roles are assigned distinct permissions: for example, managers can view the locations of all personnel, while regular employees can only see their own location.
- Visitors and contractor personnel must obtain a temporary access badge before entering the plant premises and return it upon departure.
- Data Security :
- Location data is accessible only to the safety management department, the production department, and the emergency command center.
- It is strictly prohibited to alter or disclose positioning data without authorization; violators shall be held legally accountable.
- Distribution and Collection :